For this tutorial, I have included a pattern for the bodice in sizes 3/4, 5/6 and 7/8, but you will need to measure your child so you can adjust the length of the dress to what works for you… (If you need a different size, I will show you how easy it is to make your own bodice pattern for this dress in step 1.)
The Boho Maxi Dress Tutorial:
- 2 yards of fabric (sizes 8 and under) (If your fabric has a pattern repeat that can’t turn sideways, you will need an additional 3/4 yard of fabric)
- 12 inch piece of 3/4 inch elastic
- pattern (or a well fitting tee to make your own) (Do not print directly from google docs. For the pattern to print properly, you must download it to your pc and print from adobe reader.)
- measuring tape, rulers, iron and other basic sewing supplies
Products used and recommended in this post
- My favorite fabric shops are: Etsy, Funkalicious Fabrics, Fabric.com and Girl Charlee.
- My Sewing Machine: SINGER 9960 Quantum Stylist, my coverstitch: Janome Cover Pro 1000cpx
- My Serger: Brother 1034D 3 or 4 Thread Serger or you can just use Pinking Shears
- Rotary Cutter
- I love my large ruler and large cutting mat, but you may prefer to start of with a smaller Cutting set
- Dritz Dual Purpose Marking Pen and Fray Check
- Cordless Iron
- Wonder clips (I didn’t use these in the post, but they are just awesome!
Pattern info: Seam allowances are 1/4 inch unless otherwise stated.
Step 1: Bodice Pattern
Print the front/back bodice pattern and cut out the size needed.
*Size you need not available? (Follow the directions below to make your own – click the images to make them bigger.)
Lay your bodice pattern on the fold of your fabric and cut out the front bodice piece, bodice lining and back bodice piece.
Step 2: Measurements and cutting out the rest of the pattern.
Hold the front bodice piece up to your child and measure from the bottom of the fabric to where you want the skirt to end.
(Our measurement was 28.)
The top tier should be approximately two times as tall at the bottom tier. Take your measurement and divide by 3. That number is your bottom tier and double it to get the top tier. (Technically this would make my tiers 18.6 and 9.3, but I just rounded the number to 19 and 9 – just make sure when they are added together it equals your original measurements.)
To accommodate seam allowances and hem, add 1/2 inch to the height of the top tier and 3/4 inch to the bottom tier.
Cut theses pieces:
Top tier: your height measurement (height) by 45 inches (width).
Bottom tier: your height measurement (height by 67 (width) inches.
If the pattern repeat on your fabric can be cut in any direction, you can cut the tiers in 1 piece. If not, you will need to cut the tiers in 2 pieces. (22.75 wide for the top tier and 33.75 for the bottom tier.) Tip: For sizes larger than a girls size 12, I recommend adding at least 10 inches to the width of each tier.
Straps: Cut two strips, 3 inches wide by 20 inches long.
You will have:
Step 3: Assembling the bodice.
Right sides together fold the strap piece in half and sew down the long side and one short side. Turn the strap right side out and press flat.
Lay out the front bodice piece right side up. Measure over 3/8 inch from the arm edge and pin the straps in place as shown below.
Place the bodice lining on top, right side down, pinning in place. Sew along the top and as shown below.
Trim the corner and clip a few notches in the arm curve on both sides.
Turn the bodice front right side out and press.
Reopen the bodice. Iron both side edges over, 1/4 inch.
To make the the casing on the back bottom piece, fold the fabric in half right, side facing out, and iron flat. Mark 3/8 inch from the top and draw a line side to side. Make another mark 1 inch down from the 1st mark and draw a 2nd line. Sew along these lines.
Use a safety pin and thread the elastic through the casing. Pin the elastic in place on both sides, but sew it in place on one side only.
Open the front bodice piece and fold over the the side of the back bodice piece and sew along the edge. as shown below.
To determine how long the elastic piece needs to be, try the bodice piece on your daughter.
Adjust the elastic and casing so you have a snug fit around her chest. (You can also just guesstimate based on her chest measurement and subtract 3/4 inch.) Pin the other side of the bodice in place, trimming off any excess elastic. Sew along the edge where the two pieces meet up. (Like you did on the other side.)
Step 4: Attaching the skirt.
Sew along the pinned edge using a 1/4 inch seam allowance.
Before hemming the bottom, it would be a good idea to have your little one try the dress on again and confirm the length. (Make any adjustments as needed.) Hem the bottom edge by folding over 1/4 inch, press and fold over another 1/4 inch. Press again and sew along the edge.
Here are a few more tutorials you may enjoy (plus you can find a lot more tutorials and patterns in the drop down menu bar at the top of the page.)
Don't miss any more posts! Follow along on Feedly, Bloglovin', your favorite feed reader, or signing up via email and have new posts delivered to your email box each week!